ColocatedServerConfiguration

From IntuixWiki

(Difference between revisions)
Revision as of 18:13, 23 June 2014
Sia (Talk | contribs)
General
← Previous diff
Revision as of 18:25, 23 June 2014
Sia (Talk | contribs)
OS configuration
Next diff →
Line 33: Line 33:
==== OS configuration ==== ==== OS configuration ====
- * turn on OS serial console on serial port 1, with settings as above+* turn on OS serial console on serial port 1, with settings as above
Configuring serial console: Configuring serial console:
-Linux: http://www.vanemery.com/Linux/Serial/serial-console.html+** Linux: http://www.vanemery.com/Linux/Serial/serial-console.html
-FreeBSD: http://www.freebsd.org/doc/en/books/handbook/serialconsole-setup.html+** FreeBSD: http://www.freebsd.org/doc/en/books/handbook/serialconsole-setup.html
- * permit reboot via Ctrl+Alt+Del combination if available (Linux/FreeBSD allow it by default)+* permit reboot via Ctrl+Alt+Del combination if available (Linux/FreeBSD allow it by default)
- * we also recommend adding Intuix ssh key exclusively for emergency shutdown purpose - details would be provided.+* we also recommend adding Intuix ssh key exclusively for emergency shutdown purpose - details would be provided.
===== Network configuration ===== ===== Network configuration =====
-We would provide IP provisioning information as a part of setup process.+We provide IP provisioning information as a part of setup process.
 +If we assign a (smaller than /24) block of IP addresses to you we can sub-delegate reverse DNS as per [https://tools.ietf.org/html/rfc2317#section-5.2 RFC 2317 Section 5.2 (alternative approach)].
We recommend reserving least-numbered interface (eth0) for private network and using next (eth1) for public. eth0 can be used for LOM/DRAC/IPMI (accessible from one of our shell systems); we can also provide jumpstart/kickstart/PXE boot in case of emergency through this network interface. We recommend reserving least-numbered interface (eth0) for private network and using next (eth1) for public. eth0 can be used for LOM/DRAC/IPMI (accessible from one of our shell systems); we can also provide jumpstart/kickstart/PXE boot in case of emergency through this network interface.
Line 55: Line 56:
* 216.218.215.21 * 216.218.215.21
* 38.111.192.155 * 38.111.192.155
 +
 +We can provide gratis secondary/slave DNS service for your domain by request.
==== Provisoning ==== ==== Provisoning ====

Revision as of 18:25, 23 June 2014

Contents

Colocated Server Configuration

General

- depending on location we install servers in 2-post or 4-post racks; customer is responsible for appropriate rack mounting hardware; San Jose - 2-post racks; Santa Clara - 4-post racks; if you require a shelf - please notify us beforehand

- Intuix LLC provides all cables (serial console, network and power); if you require non-standard serial console adapter you would need to supply it (we provide PC DB9F or Cyclades/Cisco RJ45M).

- please label your server with system "handle" (as assigned by Intuix LLC) on front and on the back; if available - please add mac (ethernet) address of primary (internet) interface; for example: "handleA - mac ab:cd:ef:12:34:56"; optionally you can add your company name and contact information to the label

- label network ports - especially if manufacturer labeling is wrong - i.e. "PUBLIC"

- if your system has multiple serial ports - please label console port

- please label hard drives, if they're removable, especially if your system has multiple drives; label each drive with your system handle and drive number, i.e. "handleA disk#1"; we recommend placing label on drive itself and on the front of removable drive sled

BIOS Configuration

* enable USB support and Legacy USB support, so we can use USB keyboards
* ignore POST errors (especially keyboard, floppy, etc)
* set "Power loss" mode to "Stay on"
* enable BIOS console redirection if available: 
   * COM1 (COM A)
   * Speed: 9600 baud
   * Console type: VT100, 8bit
   * Flow control: none
   * Connection type: direct connection
   * Continue redirection after boot: yet (sometimes also called "Run Agent after boot")

We can accommodate different speeds for serial console if needed but prefer default settings above.

OS configuration

  • turn on OS serial console on serial port 1, with settings as above

Configuring serial console:

  • permit reboot via Ctrl+Alt+Del combination if available (Linux/FreeBSD allow it by default)
  • we also recommend adding Intuix ssh key exclusively for emergency shutdown purpose - details would be provided.
Network configuration

We provide IP provisioning information as a part of setup process. If we assign a (smaller than /24) block of IP addresses to you we can sub-delegate reverse DNS as per RFC 2317 Section 5.2 (alternative approach).

We recommend reserving least-numbered interface (eth0) for private network and using next (eth1) for public. eth0 can be used for LOM/DRAC/IPMI (accessible from one of our shell systems); we can also provide jumpstart/kickstart/PXE boot in case of emergency through this network interface.

Here are Intuix/KOLO.NET recursive DNS nameservers which you can use in /etc/resolv.conf or as forwarders:

* 216.218.215.21
* 38.111.192.155

We can provide gratis secondary/slave DNS service for your domain by request.

Provisoning

As part of the setup you would be provided with:

  • network configuration for your server (ip/netmask/gateway), recursive DNS servers if desired
  • account on shell server for serial console and power access (you would need to send us public key for ssh access)
  • access information for console server
  • access information (host/login/password) for power controller
  • access information (URL, login/password) for bandwidth graphs